DKZ APS®

Centric APS®-Valve DKZ 103 APS®

The APS® construction indicates that the sealing element is pressed pneumatically to the perimeter of the disk in flap position “closed”! Steady pressure tightness is still guaranteed with slight wears by the constant contact pressure of the sealing element of the flap valve. Therefore it shows a special suitability for abrasive bulk material. The shut-off Valve can be employed depending on the used sealing material in a temperature range of – 40°C up to + 200°C. For the triggering of the pneumatic seal Warex offers different solutions in which the seal can, if necessary, escape freely with vacuum support or be charged with nitrogen.

  • minimized wear, by operation nearly frictionless
  • considerably extended durability with abrasive (nonadhesive) products
  • considerably lower torque, therefore smaller drives
  • maintenance-free design
  • exchangeable seals
  • EX type for application in 0/20 zones according to EC Type Examination BVS03/Atex-H024X
  • Seals with a lateral projection and an additional seal face guarantee a perfect sealing between
    flanges without additional flange seals
  • Shafts and armature head qualified for the construction of the different drive possibilities, cutting point
    according to DIN/ISO 5211
Housing
Silumin (Aluminium), steel, stainless steel
Valve Disk
stainless steel, geschliffen und poliert
Sleeve
NBR, Hypalone, EPDM, FPM, Silicone, amongst others
Shafts
stainless steel 1.4571 + 1.4057 + 1.4542
Bearing bush
MS, PTFE-coal, bronze, peek
O-Rings
NBR, FPM
  1. Body
  2. Valve Disc
  3. Seat
  4. Shaft
  5. Retaining ring
  6. O-Rings
  7. Connection flange
  8. Bearing pin
  9. Seal
  10. O-Ring
  11. Plug screw
  12. End plate
  13. Air connection APS®
  14. Mounting bracket for APS® control

1.Valve open
The special APS shut-off valve (Air-Pressure-Sealing) has a valve disc which is smaller than the corresponding sealing sleeve. The disc can close easily.

2. Valve closed
There is still a small gap remaining between the valve disc and sleeve – in this state, the fitting can be opened again with minimal torque.

3. Valve pressed
When the valve is closed, air is blown evenly on the seal, which ensures a secure and gentle shut-off with minimal friction. This is a major benefit with aggressive bulk materials, in particular.

DKZ 103 APS® DZ

Butterfly Valve with pneumatically charged sealing here with pneumatic actuator.

  • Range of Nominal Widths: DN 50 – DN 1200
  • Operating Temperature: – 40°C to + 200°C*
  • Differential Pressure: up to 6 bar*
  • Sleeve: replaceable or fix vulcanized

DKZ 110 APS® DZ

Butterfly Valve with pneumatically charged sealing here with pneumatic actuator.

  • Range of Nominal Widths: DN 50 – DN 450
  • Operating Temperature: – 40°C to + 200°C*
  • Differential Pressure: up to 6 bar*
  • Sleeve: replaceable

DKZ 110 APS® DZ-P

Butterfly Valve with pneumatically charged sealing here with pneumatic actuator. Positioner and fluid disk are particularly suitable for dosing.

  • Range of Nominal Widths: DN 50 – DN 450
  • Operating Temperature: – 40°C to + 200°C*
  • Differential Pressure: up to 6 bar*
  • Sleeve: replaceable

* Operational limitations depend on nominal width, temperature and composite materials. Crucial are the parameters set in the confirmation.

EXHIBITION DATES

Technical Days 2019 Hanau
24. – 25.09.2019

VRAC TECH-BULK TECH 2019
01. – 03.10.2019

NEWS

EXHIBITION DATES

POWTECH 2019 09. – 11.04.2019
VRAC TECH-BULK TECH 2019 01. – 03.10.2019

NEWS